LIINI® Baby Cradle: Assembly Instructions & Manual

Important information about the safety of your LIINI® product.

Sogar i dirä Schproch zum abelade. Don’t understand? Yes, Swiss German sometimes sounds a bit odd. That’s exactly why we have made the safety, use and cleaning instructions available to download in your language.

GPSR

• Safety testing: All our products are regularly tested to ensure that they pose no risk to health or safety.
• Transparent documentation: We make sure that all important information about the safe use of our products is clear and easy to understand.
• Traceability: Every product carries information about the manufacturer, importer or distributor to enable seamless tracing.

You can also find all relevant safety documents as well as use and cleaning instructions collected on the GPSR page.

All the technical data for the LIINI® baby cradle.

Certification

Our baby cradle meets the requirements of DIN EN 1466:2023, a Europe-wide standard for portable sleeping units and carry bags for young children (e.g. baby carrycots or baby carry bags).

This standard sets strict safety requirements to protect your baby as well as possible – especially when used as a baby cradle or Moses basket (e.g. on the way from the pram into the house).

The key points at a glance:

• Stability and safety: The cradle must stand securely, must not tip over and must hold the baby safely – even when the baby moves.
• Ventilation and suffocation protection: The materials and construction must ensure that your baby can breathe freely at all times.
• Notes on use: The maximum load capacity (usually 9 kg) and correct use must be clearly marked.

Dimensions and materials

Neatly packed and sorted means half the assembly is done.

Congratulations on buying the LIINI® baby cradle. Before you start assembling the baby cradle, we recommend checking the entire scope of delivery.

The best way to do this is to lay out all the screws and individual parts neatly on the floor.

The kit contains:

• 2x part (1)
• 2x part (2)
• 2x part (3)
• 2x part (4)
• 2x part (5)
• 2x part (6)
• 2x part (7)
• 1x Moses basket
• 1x side pocket for nappies or baby bottle
• Cotton bag (A) with 12 screws (45 mm)
• Cotton bag (B) with 12 round nuts
• Cotton bag (C) with 8 wooden dowels
• Cotton bag (D) with 4 screws (25 mm)
• Cotton bag (E) with hex key
• Cotton bag (F) with 4 screws (20 mm)

For smooth assembly.

Allow about 20 to 30 minutes to assemble the LIINI® baby cradle.

For environmental reasons, we do not include printed assembly instructions.

Below you can download the assembly instructions as a PDF and view them on your smartphone or tablet. You can of course also print them if needed.

• Deutsch (PDF)
• English (PDF)
• Français (PDF)
• Italiano (PDF)
• Español (PDF)
• Nederlands (PDF)
• Svenska (PDF)
• Português (PDF)

Assemble your baby cradle step by step with us.

1. 1

   Step 1: Arrange all parts neatly

   With these instructions you can easily assemble the frame of the LIINI® baby cradle step by step. Allow about 20–30 minutes and, ideally, work in pairs – it’s more fun together! Before you start assembling, we recommend laying everything out neatly. Place the individual parts of the cradle on the floor. That way you have everything within easy reach.

   

2. 2

   Step 2: Prepare the side panels

   Take the wooden parts numbered (4), (6) and (7) and insert the wooden dowels (C) from the small cotton bag into the matching pre-drilled holes. If necessary, you can use a rubber mallet.

   Make sure the dowels fit tightly – they will ensure a stable hold later on.

   

3. 3

   Step 3: Insert the round nuts

   Before you connect the side panels to the wooden legs, insert the round nuts (B) from the cotton bag into the openings provided in parts (5), (6) and (7).

   Pay attention to the correct installation direction (see picture) so that later, when tightening, you can hold the round nuts in place with the screwdriver.

   

4. 4

   Step 4: Screw the legs to the side panels

   Once you have inserted all the round nuts, you can screw the legs (5) to the prepared side panels (6) and (7). To do this, take the screws from the cotton bag (A) and use the hex key from bag (E).

   Caution

   Do not use machines

   Do not use machines to tighten the screws, as too much force can damage the baby cradle.

   

5. 5

   Step 5: Loosening-up exercises

   Admittedly, with older siblings around, assembly can take a little longer than 20–30 minutes. A bit of stretching and exercise in between won’t hurt, though.

   

6. 6

   Step 6: Attach the upper crossbars

   After the loosening-up exercises, you can now prepare the upper crossbars (3) for assembly. Here too, insert the round nuts (B) into the holes provided. Once you have done so, screw the crossbars (3) to the finished side panels (step 4). Use the screws from bag (A).

   

7. 7

   Step 7: Attach the lower crossbars

   Once the upper crossbars (3) are mounted, the lower crossbars (4) follow.

   Insert the round nuts (B) into the holes provided and screw both crossbars (4) to the side panel to which you already attached the upper crossbars in step 6. Use the screws from bag (A).

   

8. 8

   Step 8: Connect the side panels

   You’re almost there!

   Now connect the two side panels to each other and screw them together with the screws from bag (A).

   Before tightening, align the upper crossbars (3) and the lower crossbars (4) slightly so that they run parallel to each other and fit the overall look of the baby cradle.

   

9. 9

   Step 9: Attach the side Moses basket holders

   Now attach the side Moses basket holders (1) to both sides of the cradle frame using the screws (D). Make sure the threaded inserts face outwards (see picture).

   

10. 10

    Step 10: Screw on the fall protection

    Finally, screw the fall protection for the Moses basket (2) to the wooden frame. Use the screws (F).

    For this, the wood must be held lightly in position by hand so that the screw does not jam and possibly damage the thread. It is best to do this step with two people.

    

11. 11

    Step 11: Insert the Moses basket

    Congratulations, you’ve done it!

    Now place your Moses basket in the frame. Carry out a final visual check and tighten all screws once more for safety.

    

For the longevity of your cradle.

So you can enjoy the cradle for a long time

The muslin mattress cover can be removed thanks to the zip and washed without any problem in the coloured wash programme of your washing machine.

It is best to clean the Moses basket with a damp cloth and water.

Washing symbols according to GINETEX

Nobody understands them – but they have to be there.

Gentle wash at 30 °C

Gentle drying at 60 °C

Do not iron

Do not bleach

LIINI® stands for quality.

The products carry a warranty of 24 months in total from receipt of the order.

The warranty is excluded:

• If the defect is due to improper handling or use of the product that does not correspond to normal use.
• If the cradle has not been assembled in accordance with the assembly instructions or has been used contrary to the instructions in the manual (e.g. as a place for permanent sleep).
• If the Moses basket or the mattress cover has been cleaned contrary to the care instructions (e.g. with aggressive cleaning agents).
• If the defect is due to external interference (“third-party intervention”), in particular repairs and interventions by persons who have not been authorised to do so by LIINI AG.
• Normal signs of wear and tear do not give rise to a warranty claim.

LIINI AG may fulfil the warranty either by partial replacement (e.g. spare parts) or by complete replacement with an equivalent product.

To check a warranty claim, the customer must open a ticket in the ticket system at www.LIINI.ch/support and provide the following evidence:

• Video showing the problem
• Picture 1: overall view of the assembled cradle
• Picture 2: close-up of the affected area

If LIINI AG finds corresponding damage to the cradle (e.g. breaks or cracks caused by force, atypical scratches or dents, etc.), any warranty is excluded.

By submitting the ticket, the customer confirms that all information is truthful. Should it emerge during the processing of the warranty case that warranty fraud has taken place, LIINI AG reserves the right to take appropriate legal action.

According to the Product Safety Act (ProdSG).

Manufacturer identification & contact address

Responsible for the import and distribution of all products:

EU authorised representative

Exclusively for contact by authorities.